Browsing by Author "Eguía-Oller, Pablo"

Now showing 1 - 6 of 6
  • No Thumbnail Available
    Item
    Assessing the energy demand reduction in a surgical suite by optimizing the HVAC operation during off-use periods
    (Applied Sciences (Switzerland), 2020-03-25) Cacabelos, Antón; López-González, José Luis; González-Gil, Arturo; Febrero-Garrido, Lara; Eguía-Oller, Pablo; Granada-Álvarez, Enrique
    Hospital surgical suites are high consumers of energy due to the strict indoor air quality (IAQ) conditions. However, by varying the ventilation strategies, the potential for energy savings is great, particularly during periods without activity. In addition, there is no international consensus on the ventilation and hygrothermal requirements for surgical areas. In this work, a dynamic energy model of a surgical suite of a Spanish hospital is developed. This energy model is calibrated and validated with experimental data collected during real operation. The model is used to simulate the yearly energy performance of the surgical suite under different ventilation scenarios. The common issue in the studied ventilation strategies is that the hygrothermal conditions ranges are extended during off-use hours. The maximum savings obtained are around 70% of the energy demand without compromising the safety and health of patients and medical staff, as the study complies with current heating, ventilation and air conditioning (HVAC) regulations.
  • No Thumbnail Available
    Item
    Development of a calibrated simulation method for airborne particles to optimize energy consumption in operating rooms
    (Energies, 2019-06-24) Febrero-Garrido, Lara; López-González, José Luis; Eguía-Oller, Pablo; Granada-Álvarez, Enrique
    Operating rooms are stringent controlled environments. All influential factors, in particular, airborne particles, must be within the limits established by regulations. Therefore, energy efficiency stays in the background, prioritizing safety and comfort in surgical areas. However, the potential of improvement in energy savings without compromising this safety is broad. This work presents a new procedure, based on calibrated simulations, that allows the identification of potential energy savings in an operating room, complying with current airborne particle standards. Dynamic energy and airborne particle models are developed and then simulated in TRNSYS and calibrated with GenOpt. The methodology is validated through experimental contrast with a real operating room of a hospital in Spain. A calibrated model with around 2% of error is achieved. The procedure determines the variation in particle concentration according to the flow rate of ventilation supplied and the occupancy of the operating room. In conclusion, energy savings up to 51% are possible, reducing ventilation by 50% while complying with airborne particles standards.
  • No Thumbnail Available
    Item
    Estimation of heat loss coefficient and thermal demands of in-use building by capturing thermal inertia using lstm neural networks
    (Energies, 2021-08) Pensado-Mariño, Martín; Pérez-Iribarren, Estíbaliz; Granada-Álvarez, Enrique; Febrero-Garrido, Lara; Eguía-Oller, Pablo
    Accurate forecasting of a building thermal performance can help to optimize its energy consumption. In addition, obtaining the Heat Loss Coefficient (HLC) allows characterizing the thermal envelope of the building under conditions of use. The aim of this work is to study the thermal inertia of a building developing a new methodology based on Long Short-Term Memory (LSTM) neural networks. This approach was applied to the Rectorate building of the University of Basque Country (UPV/EHU), located in the north of Spain. A comparison of different time-lags selected to catch the thermal inertia has been carried out using the CV(RMSE) and the MBE errors, as advised by ASHRAE. The main contribution of this work lies in the analysis of thermal inertia detection and its influence on the thermal behavior of the building, obtaining a model capable of predicting the thermal demand with an error between 12 and 21%. Moreover, the viability of LSTM neural networks to estimate the HLC of an in-use building with an error below 4% was demonstrated.
  • No Thumbnail Available
    Item
    Feasibility of different weather data sources applied to building indoor temperature estimation using LSTM neural networks
    (Sustainability (Switzerland), 2021-12-13) Pensado-Mariño, Martín; Febrero-Garrido, Lara; Eguía-Oller, Pablo; Granada-Álvarez, Enrique
    The use of Machine Learning models is becoming increasingly widespread to assess energy performance of a building. In these models, the accuracy of the results depends largely on outdoor conditions. However, getting these data on-site is not always feasible. This article compares the temperature results obtained for an LSTM neural network model, using four types of meteorological data sources. The first is the monitoring carried out in the building; the second is a meteorological station near the site of the building; the third is a table of meteorological data obtained through a kriging process and the fourth is a dataset obtained using GFS. The results are analyzed using the CV(RSME) and NMBE indices. Based on these indices, in the four series, a CV(RSME) slightly higher than 3% is obtained, while the NMBE is below 1%, so it can be deduced that the sources used are interchangeable.
  • No Thumbnail Available
    Item
    IoT-based platform for automated IEQ spatio-temporal analysis in buildings using machine learning techniques
    (Automation in Construction, 2022-07) Troncoso-Pastoriza, Francisco; Martínez-Comesaña, Miguel; Ogando-Martínez, Ana; López-Gómez, Javier; Eguía-Oller, Pablo; Febrero-Garrido, Lara
    Providing accurate information about the indoor environmental quality (IEQ) conditions inside building spaces is essential to assess the comfort levels of their occupants. These values may vary inside the same space, especially for large zones, requiring many sensors to produce a fine-grained representation of the space conditions, which increases hardware installation and maintenance costs. However, sound interpolation techniques may produce accurate values with fewer input points, reducing the number of sensors needed. This work presents a platform to automate this accurate IEQ representation based on a few sensor devices placed across a large building space. A case study is presented in a research centre in Spain using 8 wall-mounted devices and an additional moving device to train a machine learning model. The system yields accurate results for estimations at positions and times never seen before by the trained model, with relative errors between 4% and 10% for the analysed variables.
  • No Thumbnail Available
    Item
    Optimisation of thermal comfort and indoor air quality estimations applied to in-use buildings combining NSGA-III and XGBoost
    (Sustainable Cities and Society, 2022-05) Martínez-Comesaña, Miguel; Eguía-Oller, Pablo; Martínez-Torres, Javier; Febrero-Garrido, Lara; Granada-Álvarez, Enrique
    Indoor environmental quality (IEQ) monitoring of in-use buildings has become essential in recent years due to the COVID-19 pandemic, as it significantly affects the well-being, health and productivity of building users. Nevertheless, knowing in real time the environmental conditions in large multi-zone areas is a difficult issue. Thus, the use of machine learning techniques to estimate indoor conditions has increased considerably. The aim of this paper is to present an interpolation model, based on an optimised extreme gradient boosting algorithm, to estimate every minute the indoor temperature, relative humidity and CO2 concentration inside buildings. These estimations are obtained without requiring permanent monitoring in the occupied zone. The optimisation, focused on finding the minimum number of monitoring devices needed to provide accurate interpolations, is performed using the multi-objective genetic algorithm NSGA-III. This methodology was applied in a research centre in the north-western Spain. The results show that the optimised or reduced model is capable of estimating indoor temperatures and relative humidity with relative errors below 6% and CO2 levels below 10%.